Use Code: BFCM20 & Save $20 Off Your Order Over $200+

Free Shipping in the Contiguous US Learn More

Use Code: NINJA & Save 20% Off Your First Order Of Transfers

SAVE $20 ON ORDERS OF $200+

BFCM20
USE CODE: BFCM20

Ryonet Discharge Agent

Ryonet  |  SKU: IKDC-DISAGENT-LB
Size
$31.95
1.25 lb
Flat rate
multi-qty message
In stock
DESCRIPTION
Discharge Agent is the activation component for discharge printing. This agent can only be used in combination with a finished Discharge Ink like Discharge Base, Discharge White, or Ryo Charge in order for discharging to take place. Discharge Agent comes in a crystalline powder form and is sold and shipped by the pound. To activate a discharge ink, mix discharge agent into the final ink at about 4-6% of the final weight.

Example: When mixing 350 grams of a discharge color, your discharge base may only be around 300 grams of the total formula. Yet you measure out the discharge activator, based on the total final weight of 350 grams.

Activator should always be the last item added, after the ink and ink components have been blended together. When mixing, blend the agent slowly into the ink until it is beginning to dissolve, then continue to mix well at higher speeds for up to 1 minute. Let the ink sit for 5-10 minutes before testing or going into production to ensure full dispersion of the crystals into your ink.

We strongly recommend using a gram scale for optimal mixing performance.

How Discharge Works and Proper Cure
Discharge agent is a compound molecule. That compound is Zinc Formaldehyde Sulfoxylate. The discharge process begins from high heat, either during flashing or curing, breaking apart the activator molecule. Once the activator is in its separate components, the formaldehyde attaches to the fabric dye and breaks the dye molecule. It's this process which removes the color from the garment you are printing on. However, not all dyes react well and are considered “nondischargeable”. So check with your garment manufacturer for a dischargeability rating chart.

After the garment dye is removed (this process happens at 250°F) you need to continue to heat up the ink layer and get a FULL cure of your entire ink layer. Water-based ink cures once the entire ink layer is at “cure temp” and it holds at that temp. 320°F is the target temperature here in the U.S. At this temp you need to hold at or above 320°F for 20-30 seconds. If this means that you need to keep the garment in the dryer for 3 minutes to reach 320° and hold at or above that temp for 20-30 seconds, then that is how long you need to keep your shirt in the dryer to achieve a durable print.

At the end of the discharge process and during cure, the formaldehyde combines with the sulfur to create an inert molecule. As always, make sure you vent all air from the dryer to the outside. Some people have an itchy or swelling reaction when handling the discharge agent, what they are reacting to is the Sulfur in the activator. About 3% of the population have a sulfur allergy.

If you are unable to keep your shirt at those cure parameters, you can add Warp Drive to your ink. When you do this, you need to make sure that a FULL discharge of the garment happens. A full discharge of the garment only happens after you have removed all of the water in the ink and the ink reaches 250°F. So this is a great indicator that you have met all the parameters needed for the Warp Drive to activate.

As always, test before running production.
SCREEN PREPARATION

Screens must be coated with a water Resistant emulsion, we recommend using a water-resistant emulsion like Baselayr Complete emulsion. For extended screen life and long print runs it is recommended to post expose the screens and/or use an emulsion hardener like Baselayr emulsion hardener.

For all Ink Applications, Print Parameters, Cure and ink Clean Up Procedures: See the relevant ink type section:
Discharge Base
Discharge White
RyoCharge

**As of Feb 2024, the 40 lb (5G) bag was replaced with a 55 lb bag** 

PRODUCT DATA SHEETS
FREE GROUND SHIPPING (SUPPLIES ONLY)

FREE SHIPPING

All supplies in orders over $275 ship for free. Orders below $275 ship for $15. Orders placed before 3pm local time typically ship the same day.

FLAT RATE SHIPPING

Flat rate shipping charges will be assigned to our Equipment and heavier consumable items. View our entire FREE Shipping Policy

GROUND SHIPPING ZONES

UPS Ground Shipping Zones

If you need clarity on estimated shipping to your area please chat with us or call us at 1-800-314-6390

POPULAR PRODUCTS

VIEW MORE
Riley Hopkins 360 screen printing press set up with multiple screens in vibrant colors, ready for multi-color printing. A printed shirt with a detailed, colorful design is positioned on the platen, showcasing the precision and versatility of the screen printing process.

RILEY HOPKINS

MANUAL PRESSES

SHOP THE COLLECTION
Person holding a scoop coater filled with bright blue emulsion, positioned next to a screen ready for coating. The setup highlights the preparation stage of screen printing, where precision and even coverage are key for creating quality stencils.

INDUSTRY LEADING

EMULSIONS

BUY NOW

PLASTISOL INK

MIXING SYSTEMS

GRAB YOURS
Screen exposure unit with a glowing orange and blue light, holding a screen and Baselayr output film in place. The darkroom setup emphasizes the precision and technology used to create sharp, detailed stencils for screen printing.

BASELAYR

LED EXPOSURE UNITS

ORDER NOW

THINGS YOU SHOULD KNOW

View all
Ryonet Discharge Agent | Screenprinting.com
Ryonet

Ryonet Discharge Agent

From $31.95
Discharge Agent is the activation component for discharge printing. This agent can only be used in combination with a finished Discharge Ink like Discharge Base, Discharge White, or Ryo Charge in order for discharging to take place. Discharge Agent comes in a crystalline powder form and is sold and shipped by the pound. To activate a discharge ink, mix discharge agent into the final ink at about 4-6% of the final weight.

Example: When mixing 350 grams of a discharge color, your discharge base may only be around 300 grams of the total formula. Yet you measure out the discharge activator, based on the total final weight of 350 grams.

Activator should always be the last item added, after the ink and ink components have been blended together. When mixing, blend the agent slowly into the ink until it is beginning to dissolve, then continue to mix well at higher speeds for up to 1 minute. Let the ink sit for 5-10 minutes before testing or going into production to ensure full dispersion of the crystals into your ink.

We strongly recommend using a gram scale for optimal mixing performance.

How Discharge Works and Proper Cure

Discharge agent is a compound molecule. That compound is Zinc Formaldehyde Sulfoxylate. The discharge process begins from high heat, either during flashing or curing, breaking apart the activator molecule. Once the activator is in its separate components, the formaldehyde attaches to the fabric dye and breaks the dye molecule. It's this process which removes the color from the garment you are printing on. However, not all dyes react well and are considered “nondischargeable”. So check with your garment manufacturer for a dischargeability rating chart.

After the garment dye is removed (this process happens at 250°F) you need to continue to heat up the ink layer and get a FULL cure of your entire ink layer. Water-based ink cures once the entire ink layer is at “cure temp” and it holds at that temp. 320°F is the target temperature here in the U.S. At this temp you need to hold at or above 320°F for 20-30 seconds. If this means that you need to keep the garment in the dryer for 3 minutes to reach 320° and hold at or above that temp for 20-30 seconds, then that is how long you need to keep your shirt in the dryer to achieve a durable print.

At the end of the discharge process and during cure, the formaldehyde combines with the sulfur to create an inert molecule. As always, make sure you vent all air from the dryer to the outside. Some people have an itchy or swelling reaction when handling the discharge agent, what they are reacting to is the Sulfur in the activator. About 3% of the population have a sulfur allergy.

If you are unable to keep your shirt at those cure parameters, you can add Warp Drive to your ink. When you do this, you need to make sure that a FULL discharge of the garment happens. A full discharge of the garment only happens after you have removed all of the water in the ink and the ink reaches 250°F. So this is a great indicator that you have met all the parameters needed for the Warp Drive to activate.

As always, test before running production.

SCREEN PREPARATION

Screens must be coated with a water Resistant emulsion, we recommend using a water-resistant emulsion like Baselayr Complete emulsion. For extended screen life and long print runs it is recommended to post expose the screens and/or use an emulsion hardener like Baselayr emulsion hardener.

For all Ink Applications, Print Parameters, Cure and ink Clean Up Procedures: See the relevant ink type section:
Discharge Base
Discharge White
RyoCharge

**As of Feb 2024, the 40 lb (5G) bag was replaced with a 55 lb bag** 

PRODUCT DATA SHEETS

Size

  • 1 Lb
  • 55 Lbs
View product

TOP-TIER SERVICE
Back to top